Process Knowledge

When to specify stress relief after SLM 316L

When to specify stress relief after SLM 316L: process class, sequence, and rates.v1.1 estimate packaging—Example part only.

By 3DWK Engineering Team · · 5 min read

Example part SLM 316L bracket map showing labeled stress relief required, process class cited, sequence after supports and before HIP or machining if cited, other faces as-built
Illustration: 3DWK original diagram (typical values, not to scale).

The short answer

**Stress relief** after SLM 316L is not a synonym for [HIP](https://3dwk.com/resources/when-to-specify-hip-after-slm-parts), not a cousin of [T6 aging on SLM AlSi10Mg](https://3dwk.com/resources/when-to-specify-t6-aging-after-slm-alsi10mg), and not the same pack as [stress relief after CNC aluminum](https://3dwk.com/resources/when-to-specify-stress-relief-after-cnc-aluminum) or a general [residual-stress and warpage note](https://3dwk.com/resources/slm-residual-stress-warpage-notes-for-buyers). A usable callout says **whether stress relief is required**, the **heat-treat or stress-relief class you actually use**, and the **sequence** versus support removal, HIP, and machining stock. Silence, or a note that only says “stress relieve as needed,” is what widens many [quote-new.php](https://3dwk.com/quote-new.php) **rates.v1.1** estimate bands—not the furnace hours alone.

This guide is for buyers packaging SLM 316L parts that need a named stress-relief step before or after finishing. Illustrations use an **Example part** only—not a customer implant or bracket, and not a fabricated heat-treat chart. Sibling notes cover warpage, HIP, and machining allowance; here we focus on **when a stress-relief pack is worth calling out**, including the class and sequence the buyer actually uses.

What stress relief after SLM 316L means for quoting

A **stress-relief pack** names that a thermal stress-relief step is required, which class or buyer standard applies (only if that is what you use), and the sequence relative to support removal, any HIP, and [machining stock](https://3dwk.com/resources/when-to-specify-machining-stock-allowance-slm-parts). Writing “stress relieve as needed” or “heat treat the print” is not enough. Process pages for common SLM 316L work ([SLM 316L medical](https://3dwk.com/en/slm/316l/medical.html), [SLM 316L aerospace](https://3dwk.com/en/slm/316l/aerospace.html), [SLM 316L](https://3dwk.com/en/slm/316l.html)) assume the pack is visible when lots mix as-built, stress-relieved, HIPed, and machined 316L.

Do not bury “stress relieve for stability” inside a notes cloud. Put **STRESS RELIEF: REQUIRED; CLASS OR STANDARD CITED; AFTER SUPPORTS / BEFORE OR AFTER HIP AND MACHINING AS WRITTEN** on the PDF and mirror it in RFQ text. If no stress relief is required, say **NO STRESS RELIEF; OTHER HEAT TREAT CITED IF ANY** so the shop does not have to guess. Background: [what files to send for a CNC quote](https://3dwk.com/resources/what-files-to-send-for-cnc-quote), [SLM residual stress and warpage notes](https://3dwk.com/resources/slm-residual-stress-warpage-notes-for-buyers).

Vague stress-relieve-as-needed RFQ versus labeled class-sequence pack — Example part
Illustration: 3DWK original diagram (typical values, not to scale).

When the stress-relief pack is worth calling out

Specify stress relief when the program actually requires a thermal cycle to reduce build residual stress, and when you are prepared to cite the class or standard the program uses. Skip a blanket furnace note on a prototype still accepted as-built, and do not use stress relief as a substitute for HIP (density), for a solution or other 316L heat-treat class you have not named, or for T6 on an aluminum SLM grade.

If you cite a class, a standard, or a buyer specification, write the **document and class on the PDF**. This guide does not invent a temperature, a hold time, a heat-up or cool-down rate, an atmosphere, or a 3DWK-standard stress-relief recipe. Furnace time is rarely the whole **rates.v1.1** story—sequence versus supports, HIP, and machining is.

Sequence versus supports, HIP, and machining

Name the order: as-built, support removal or a skim, stress relief, any HIP, then machining of stock faces if those are cited. Stress relief before support removal is a different RFQ from stress relief after supports and before machining. If HIP is also required, say whether stress relief is still required, replaced, or sequenced around HIP—do not leave two furnace notes to fight. [Machining allowance](https://3dwk.com/resources/when-to-specify-machining-stock-allowance-slm-parts), when needed, stays on its own line with the faces and stock you actually want. Fixture or datum faces that must stay stable through the furnace belong in that same sequence note.

Tolerance and inspection traps

Calling “stress relieve as needed,” asking to “heat treat the SLM part” with no class, or demanding a residual-stress or hardness result without a method, all force **needs_manual**. Default an as-built coupon or a part that already names a different 316L heat-treat class to an explicit pack; do not let stress relief appear as an implied default on every 316L build. Related: [what needs_manual means](https://3dwk.com/resources/what-needs-manual-means-preliminary-quote).

Illustration 1 shows an **Example part** SLM 316L bracket with labeled stress relief required, class cited by the buyer, sequence after supports and before HIP or machining if those are cited, versus as-built surfaces left without a furnace step.

Example part walkthrough

**Example part:** SLM 316L bracket, stress relief required, buyer heat-treat or stress-relief class cited, after support removal and before HIP or machining if those steps are also cited, no invented temperature, hold time, or 3DWK furnace recipe. With STEP + **STRESS RELIEF REQUIRED; CLASS CITED; AFTER SUPPORTS, BEFORE HIP / MACHINING AS WRITTEN**, expect a usable automatic planning band on [quote-new.php](https://3dwk.com/quote-new.php). Same geometry with silent “stress relieve as needed” often lands DFM notes or **needs_manual**—without inventing any customer implant, residual-stress certificate, or a 3DWK-guaranteed distortion result.

Illustration 2 contrasts a vague RFQ (“stress relieve as needed”) versus a labeled class-sequence pack and the clearer estimate path.

What widens bands fastest

Unlabeled “as needed” stress relief, a “heat treat the print” note that never names the class, sequence left silent versus supports, HIP, and machining, and a residual-stress demand with no method. Quantity breaks do not erase finish-pack ambiguity—see [how quantity breaks change CNC unit cost](https://3dwk.com/resources/how-quantity-breaks-change-cnc-unit-cost).

What to do next

Mark the RFQ with **required or not, the heat-treat or stress-relief class you use, and sequence versus supports, HIP, and machining**, then upload the CAD on [quote-new.php](https://3dwk.com/quote-new.php). Packaging checklist: stress relief is not HIP, not T6, and not a machining-stock note; keep those on their own lines. Service pages: [3D printing](https://3dwk.com/3d-printing-service.php), [materials](https://3dwk.com/materials.php). Treat **rates.v1.1** min/mid/max as estimates, not invoices. If the UI shows **needs_manual**, answer the stress-relief-pack questions rather than forcing a fake price.

Common questions

Is stress relief the same as HIP or as T6 on aluminum SLM?

No. HIP is a densification cycle at a cited class; T6 aging applies to aluminum alloys such as AlSi10Mg, not to 316L. Stress relief is a thermal cycle you name when the 316L program requires it. Package the process you actually need.

Does every SLM 316L part need stress relief?

No. Specify it when the program actually requires that class. An as-built prototype should not inherit a “stress relieve as needed” note by default, and a part that already names a different 316L heat-treat class should say whether stress relief is still required.

Can 3DWK just use a standard temperature and hold time?

Cite the standard and class you need on the PDF. This guide does not invent a temperature, a hold time, or a furnace recipe as a 3DWK guarantee.

Where do supports, HIP, and machining sit versus stress relief?

Write the order. Stress relief before support removal is a different pack from a cycle after supports and before machining or HIP. Keep HIP and machining-stock notes on their own lines.

Free DFM · 24h quote

Upload CAD → free DFM report

Email required. You get a link to a rule-based manufacturability checklist (not a formal engineering sign-off). Engineers still review pricing.

No CAD? Photo / description → 24h quote

Three fields only — we reply within 24 hours.

Next step

Questions about your design?

Upload CAD files and an engineer will review manufacturability with your quote.

Upload CAD