Quality and Inspection

When to specify T6 aging after SLM AlSi10Mg

When to specify T6 aging after SLM AlSi10Mg: condition, sequence and rates.v1.1 estimate packaging—Example part only.

By 3DWK Engineering Team · · 6 min read

Example part AlSi10Mg SLM bracket map showing labeled T6 / aging after support removal and after HIP if cited, before the skim of datum A, versus as-built ribs with no aging requirement
Illustration: 3DWK original diagram (typical values, not to scale).

The short answer

A **T6 / aging heat treat** after SLM AlSi10Mg is not a default cycle on every printed bracket, and it is not a synonym for [HIP](https://3dwk.com/resources/when-to-specify-hip-after-slm-parts), [porosity sealant](https://3dwk.com/resources/when-to-specify-porosity-sealant-after-slm-aluminum), [CT inspection](https://3dwk.com/resources/when-to-specify-ct-inspection-after-slm-parts), or a [stress-relief note written for CNC aluminum](https://3dwk.com/resources/when-to-specify-stress-relief-after-cnc-aluminum). A usable callout says **whether a peak-aged or T6-type condition is required**, **which standard or property target you actually cite** (cite the document, do not assume a 3DWK recipe), and the **sequence** versus build-plate removal, stress relief, HIP, support removal, machining, and finish. Silence, or a note that only says “T6 as needed,” is what widens many [quote-new.php](https://3dwk.com/quote-new.php) **rates.v1.1** estimate bands—not the furnace cycle alone.

This guide is for buyers packaging AlSi10Mg SLM parts whose mechanical condition must be named, not left as-built. Illustrations use an **Example part** only—not a customer bracket, and not a fabricated hardness or tensile result. Sibling notes live in the HIP, sealant, and CT guides; here we focus on **when a T6 / aging pack is worth calling out**. Wrought T6 language is not a drop-in for SLM AlSi10Mg.

What T6 / aging after SLM AlSi10Mg means for quoting

A **T6 / aging callout** names that the printed AlSi10Mg part must be placed in a specified heat-treated condition—often described as peak aging or a T6-type temper borrowed from wrought aluminum—rather than left as-built or only stress-relieved. Writing “T6 as needed” or “heat treat for strength” is not enough. Process pages for AlSi10Mg SLM ([SLM AlSi10Mg aerospace](https://3dwk.com/en/slm/alsi10mg/aerospace.html), [SLM AlSi10Mg](https://3dwk.com/en/slm/alsi10mg.html), [SLM AlSi10Mg automation](https://3dwk.com/en/slm/alsi10mg/automation.html)) assume the condition pack is visible when lots mix as-built prototypes and peak-aged structural brackets.

Do not bury “age as needed” inside a notes cloud. Put **T6 / AGING: REQUIRED AFTER SUPPORT REMOVAL (AND AFTER HIP IF HIP IS CITED), BEFORE SKIM OF DATUM A; CONDITION / STANDARD CITED** on the PDF and mirror it in RFQ text. If as-built or stress-relieved only is accepted, say **NO T6 / NO PEAK AGING** so the shop does not have to guess. Background: [SLM residual stress and warpage notes](https://3dwk.com/resources/slm-residual-stress-warpage-notes-for-buyers), [SLM support removal and skim notes](https://3dwk.com/resources/slm-support-removal-and-skim-notes), [what files to send for a CNC quote](https://3dwk.com/resources/what-files-to-send-for-cnc-quote).

Vague T6-as-needed RFQ versus labeled condition-sequence pack — Example part
Illustration: 3DWK original diagram (typical values, not to scale).

When the aging pack is worth calling out

Specify a T6 / aging step when the program requires a named peak-aged condition, when as-built strength is not accepted, or when machining of datums is planned after the heat treat so the skim sees the stable condition. Skip a blanket T6 on a fit-check print whose notes still say “as built, no property target,” and do not use aging as a substitute for HIP, for sealant, or for CT. Aging changes the temper; it does not close porosity the way HIP or impregnation does, and it is not an internal-inspection report.

If you cite a standard or a property target (hardness or tensile), write the **document and the target on the PDF**. This guide does not invent a solution or aging temperature, a soak time, or a 3DWK-guaranteed property band. Material cost is rarely the aging-pack story under **rates.v1.1**—condition, sequence, and any HIP line are.

Sequence versus HIP, machining, and finish

Name the order: print, plate removal, any stress relief, HIP if required, T6 / aging if required, then [support removal and skim](https://3dwk.com/resources/slm-support-removal-and-skim-notes) or machine of datum A, then anodize or chem film unless the drawing places finish earlier and says why. Aging before a large skim of datum A is a different RFQ from aging after finish machine. Keep HIP, sealant, and CT on their own lines. A wrought [heat-treat-after-CNC](https://3dwk.com/resources/when-to-specify-heat-treat-after-cnc) note is not a substitute for this SLM condition pack.

Tolerance and inspection traps

Calling “T6 as needed,” asking to “heat treat for strength” with no condition or standard, or demanding a hardness or tensile result without a method and a target, all force **needs_manual**. Default cosmetic or fit-check SLM brackets to an explicit no-aging or as-built condition; reserve a named T6 / aging step for parts that actually have a property target. Related: [what needs_manual means](https://3dwk.com/resources/what-needs-manual-means-preliminary-quote).

Illustration 1 shows an **Example part** AlSi10Mg SLM bracket with labeled T6 / aging after support removal and after HIP if HIP is cited, before the skim of datum A, versus cosmetic ribs left as-built with no aging requirement.

Example part walkthrough

**Example part:** AlSi10Mg SLM bracket ~80 × 50 × 30 mm, T6 / aging required after support removal (and after HIP if HIP is on the same RFQ) and before skim of datum A, condition or standard cited by the buyer, no invented soak temperature, time, hardness, or tensile result. With STEP + **T6 / AGING REQUIRED AFTER SUPPORT REMOVAL AND AFTER HIP IF CITED, BEFORE SKIM OF DATUM A; CONDITION / STANDARD CITED**, expect a usable automatic planning band on [quote-new.php](https://3dwk.com/quote-new.php). Same geometry with silent “T6 as needed, make it strong” often lands DFM notes or **needs_manual**—without inventing any customer PO, lab certificate, or a 3DWK-guaranteed property band.

Illustration 2 contrasts a vague RFQ (“T6 as needed”) versus a labeled condition-sequence pack and the clearer estimate path.

What widens bands fastest

Unlabeled “as needed” T6, a demand to “heat treat for strength” with no standard, a sequence that is silent versus HIP or the skim of datum A, and a hardness demand with no method. Quantity breaks do not erase condition-pack ambiguity—see [how quantity breaks change CNC unit cost](https://3dwk.com/resources/how-quantity-breaks-change-cnc-unit-cost).

What to do next

Mark the RFQ with **required or not, the condition or standard you cite, and sequence versus HIP, support removal, and the skim of datums**, then upload on [quote-new.php](https://3dwk.com/quote-new.php). Packaging checklist: HIP, sealant, and CT on their own lines, then the aging pack, then finish. Service pages: [3D printing](https://3dwk.com/3d-printing-service.php), [materials](https://3dwk.com/materials.php). Treat **rates.v1.1** min/mid/max as estimates, not invoices. If the UI shows **needs_manual**, answer the condition-pack questions rather than forcing a fake price.

Common questions

Does every SLM AlSi10Mg part need a T6 / aging cycle?

No. Specify aging when a named peak-aged condition is actually required. As-built or stress-relieved-only prototypes should not inherit a “T6 as needed” note by default.

Is T6 a substitute for HIP, sealant, or CT?

No. HIP densifies the material; sealant impregnates interconnected porosity; CT looks inside it; aging changes the temper. They can appear on the same RFQ, but each belongs on its own line with its own sequence.

Can 3DWK just use a standard furnace recipe?

Cite the standard or property target you need on the PDF. This guide does not invent a solution or aging temperature, a soak time, or a guaranteed hardness or tensile result.

Where does machining sit versus aging?

Usually after the T6 / aging step so the skim of datum A sees the heat-treated condition, unless the drawing places a different order and says why. Write the order.

Free DFM · 24h quote

Upload CAD → free DFM report

Email required. You get a link to a rule-based manufacturability checklist (not a formal engineering sign-off). Engineers still review pricing.

No CAD? Photo / description → 24h quote

Three fields only — we reply within 24 hours.

Next step

Questions about your design?

Upload CAD files and an engineer will review manufacturability with your quote.

Upload CAD