Design Guides

Center-hole notes on CNC turned shafts

Center-hole notes on CNC turned shafts: form, size, remain-or-remove, and rates.v1.1 estimate packaging—Example part only.

By 3DWK Engineering Team · · 6 min read

Example part SS 304 shaft map showing labeled Type B center holes both ends, size cited, remaining on the finished part, kept out of journal B and the M10 thread
Illustration: 3DWK original diagram (typical values, not to scale).

The short answer

A **center hole** (the center-drill / between-centers seat at a shaft end) is not a license to write only “center both ends as needed,” and it is not the same note as a [thread relief](https://3dwk.com/resources/thread-relief-runout-notes-cnc-turned-parts) or a [shoulder undercut](https://3dwk.com/resources/shoulder-fillet-vs-undercut-cnc-turned-shafts). A usable callout names the **form or standard** you actually use (for example a buyer-cited DIN 332 or ISO 866 type A, B, or R—cite the document, do not assume a 3DWK default), the **size**, the **included angle** if it is not fixed by that standard, **which ends** get a center, and whether the center **remains on the finished part** or is a manufacturing aid that must be removed after turning or [OD grinding](https://3dwk.com/resources/when-is-od-grinding-needed-after-cnc-turning). Silence on remain-versus-remove, or a note that only says “center drill,” is what widens many [quote-new.php](https://3dwk.com/quote-new.php) **rates.v1.1** estimate bands.

This guide is for buyers packaging turned shafts that will be held between centers, ground on centers, or inspected on centers. Illustrations use an **Example part** only—not a customer shaft, and not a fabricated runout report. Sibling notes live in the OD-grinding guide and the [turned stainless shaft drawing guide](https://3dwk.com/resources/turned-stainless-shaft-drawing-guide); here we focus on **center-hole packaging**, not on [keyways](https://3dwk.com/resources/keyway-callouts-on-cnc-turned-shafts) or [wrench flats](https://3dwk.com/resources/wrench-flat-notes-cnc-turned-shafts).

What center holes mean for quoting

A **center-hole callout** says the shaft will be supported, driven, or inspected from a conical seat at one or both ends. Form, size, and remain-or-remove travel together; a tiny Type A seat that must stay on a cosmetic end is a different RFQ from a protected Type B seat that will be faced off after grind. Writing “centers as needed” or “standard center drill” is not enough. Process pages for stainless turning ([CNC turning SS 304 automation](https://3dwk.com/en/cnc-turning/ss-304/automation.html), [CNC turning SS 304](https://3dwk.com/en/cnc-turning/ss-304.html), [CNC 3-axis SS 304 automation](https://3dwk.com/en/cnc-3axis/ss-304/automation.html)) assume the center-hole pack is visible when lots mix workholding centers, remaining centers, and faced-off ends on the same shaft family.

Do not bury “center both ends” inside a notes cloud. Put **CENTER HOLE BOTH ENDS: TYPE / SIZE CITED, REMAIN ON FINISHED PART (OR REMOVE AFTER GRIND), KEEP OUT OF M10 AND JOURNAL B** on the PDF and mirror it in RFQ text. If no center is allowed on a finished end, say **NO CENTER HOLE; FACE / CHAMFER ONLY** so the shop does not have to guess. Background: [what files to send for a CNC quote](https://3dwk.com/resources/what-files-to-send-for-cnc-quote), [DFM checklist before an online CNC quote](https://3dwk.com/resources/dfm-checklist-before-online-cnc-quote).

Vague center-both-ends RFQ versus labeled form-size-remain pack — Example part
Illustration: 3DWK original diagram (typical values, not to scale).

Form, size, and remain-versus-remove

Name the form and the size together. A Type A (plain 60°) seat, a Type B seat with a protecting chamfer, and a radiused Type R seat are not interchangeable leftovers; if you cite a standard, write the type and the size the shop must cut. Do not ask 3DWK to invent a default drill diameter or a depth as a process guarantee. Then say whether the center **remains** on the finished shaft or **must be removed** after turning or after a grind of journal B.

If only one end may have a center, say which end. If a thread or a [retaining-ring groove](https://3dwk.com/resources/retaining-ring-groove-notes-cnc-shafts) already occupies an end, write the keep-out. Do not assume a center can share an end with an M10 thread unless the drawing says so.

Location, keep-outs, and later grinding

A center that will later support an [OD grind](https://3dwk.com/resources/when-is-od-grinding-needed-after-cnc-turning) has to still locate the journal. Say whether the same centers are used for turning and grinding, and whether they stay after the grind. Keep-outs belong on the same line: minimum land to journal B and to any thread. Do not use “turn on centers” as a substitute for a named runout frame—see [concentricity versus runout](https://3dwk.com/resources/concentricity-vs-runout-callouts-cnc-shafts).

Tolerance and inspection traps

Calling “center drill as needed,” leaving remain-versus-remove silent, or demanding a runout result “from the centers” with no journal datum, all force **needs_manual**. Default cosmetic ends to an explicit no-center or a named remain-on-part form. Related: [what needs_manual means](https://3dwk.com/resources/what-needs-manual-means-preliminary-quote).

Illustration 1 shows an **Example part** SS 304 shaft with labeled Type B center holes both ends, size cited, remaining on the finished part, kept out of journal B and the M10 thread.

Example part walkthrough

**Example part:** SS 304 turned shaft ~Ø20 × 120 mm, center holes both ends to a buyer-cited Type B size, centers remain on the finished part, journal B ground on the same centers, M10 thread and journal B kept out of the center-drill, no invented drill depth or 3DWK-standard diameter. With STEP + **CENTER HOLES BOTH ENDS, TYPE B SIZE CITED, REMAIN ON PART, GRIND JOURNAL B ON SAME CENTERS, KEEP M10 AND JOURNAL B**, expect a usable automatic planning band on [quote-new.php](https://3dwk.com/quote-new.php). Same geometry with silent “center drill as needed” often lands DFM notes or **needs_manual**—without inventing any customer PO, runout certificate, or a 3DWK-guaranteed center-hole size.

Illustration 2 contrasts a vague RFQ (“center both ends”) versus a labeled form-size-remain pack and the clearer estimate path.

What widens bands fastest

Unlabeled “as needed” centers, a remain-versus-remove silence on a cosmetic end, a center that collides with a thread, and a grind note that assumes centers exist but never calls them out. Quantity breaks do not erase that ambiguity—see [how quantity breaks change CNC unit cost](https://3dwk.com/resources/how-quantity-breaks-change-cnc-unit-cost).

What to do next

Mark each end with **form and size (and the standard if you cite one), remain or remove, which ends, and keep-outs**, then upload on [quote-new.php](https://3dwk.com/quote-new.php). Packaging checklist: workholding versus finished-feature intent, any grind that will reuse the centers, and ends that must stay blank. Service pages: [CNC machining](https://3dwk.com/cnc-machining-service.php), [materials](https://3dwk.com/materials.php). Treat **rates.v1.1** min/mid/max as estimates, not invoices. If the UI shows **needs_manual**, answer the center-hole questions rather than forcing a fake price.

Common questions

Is a center hole the same as a chamfered end?

No. A chamfer is an edge break; a center hole is a conical seat for a center, a driver, or an inspection point. Writing only “chamfer both ends” does not authorize a center drill.

Do I have to name a standard if I only want manufacturing centers?

Name the form and size even for manufacturing-only seats, and write **REMOVE AFTER TURN / GRIND** if the finished end must be clean. A “standard center drill” note still leaves the type and the remain-or-remove decision unstated.

Can the center break into a thread or a snap-ring groove?

Only if you say so. A default keep-out is safer: give a minimum land to the thread, the groove, and journal B. If a short shaft has no room, write the allowed exception on the PDF.

How should I inspect a remaining center?

Call out the form, the size (or a gage), and any runout of the journals from the same centers you intend to use. Do not leave “turn between centers” as the only acceptance note.

Free DFM · 24h quote

Upload CAD → free DFM report

Email required. You get a link to a rule-based manufacturability checklist (not a formal engineering sign-off). Engineers still review pricing.

No CAD? Photo / description → 24h quote

Three fields only — we reply within 24 hours.

Next step

Questions about your design?

Upload CAD files and an engineer will review manufacturability with your quote.

Upload CAD