Design Guides

Flange bolt-circle position notes for CNC housings

Flange bolt-circle position notes for CNC housings: PCD, hole count, true position and rates.v1.1 estimate packaging—Example part only.

By 3DWK Engineering Team · · 6 min read

Example part Al 6061 housing map showing a labeled PCD 60, 6 by 6.6 bolt circle, first hole on datum B, pattern true position, and named flange-face flatness
Illustration: 3DWK original diagram (typical values, not to scale).

The short answer

A **flange bolt circle** on a CNC housing is not a handful of clearance holes that “can be a bit loose,” and it is not a license to write only “PCD as needed.” A usable callout names the **pitch-circle diameter (PCD / BCD)**, the **hole count and size**, whether the holes are clearance, tapped, or a mix, the **true position of the pattern** versus any individual hole, the **clocking** from a named datum, and how **flange-face flatness** interacts with the pattern. Silence on pattern position versus one-hole position is what widens many [quote-new.php](https://3dwk.com/quote-new.php) **rates.v1.1** estimate bands—not the extra minutes of a drill cycle alone.

This guide is for buyers packaging milled aluminum housings where a cover, motor, or valve body bolts on a circular pattern, but the drawing shows only a ring of holes or a note that says “bolt circle for M6.” Illustrations use an **Example part** only—not a customer housing. Sibling notes live in [dowel-pin hole location](https://3dwk.com/resources/dowel-pin-hole-location-dfm-cnc), [counterbore, countersink, and spotface notes](https://3dwk.com/resources/counterbore-countersink-spotface-cnc-bolted-joints), and [position versus profile on CNC brackets](https://3dwk.com/resources/position-vs-profile-tolerances-cnc-brackets); here we focus on **bolt-circle pattern packaging**, not on a single dowel pair or a lone countersink.

What flange bolt-circle position means for quoting

A **bolt-circle callout** names the PCD, the number of holes, the hole size and class (clearance or tapped), the clocking of the first hole from a datum, and whether true position applies to the pattern as a group, to each hole, or both. Writing “standard 6× M6 flange” is not enough. Process pages for aluminum housing milling ([CNC 3-axis Al 6061 automation](https://3dwk.com/en/cnc-3axis/al-6061/automation.html), [CNC 5-axis Al 6061 automation](https://3dwk.com/en/cnc-5axis/al-6061/automation.html), [CNC 3-axis Al 6061](https://3dwk.com/en/cnc-3axis/al-6061.html)) assume the pattern scheme is visible when lots mix clearance holes, tapped holes, and dowels on the same flange.

Do not bury “bolt circle as needed” inside a notes cloud. Put **BOLT CIRCLE A: PCD 60, 6× Ø6.6, FIRST HOLE ON DATUM B, TRUE POSITION OF THE PATTERN FROM A/B/C, FACE FLATNESS NAMED** on the PDF and mirror it in RFQ text. If two holes are actually dowels, say so and point to the dowel guide rather than hiding them in the clearance count. Background: [designing bosses and ribs for CNC housings](https://3dwk.com/resources/designing-bosses-and-ribs-for-cnc-housings), [five-axis aluminum housing design tips](https://3dwk.com/resources/five-axis-aluminum-housing-design-tips), [what files to send for a CNC quote](https://3dwk.com/resources/what-files-to-send-for-cnc-quote).

Vague standard-flange RFQ versus labeled PCD-count-clocking-position pack — Example part
Illustration: 3DWK original diagram (typical values, not to scale).

PCD, hole count, and clocking

Name the pitch-circle diameter as a dimensioned diameter, not only as a CAD sketch. Name the hole count and whether every hole is the same size. Clock the first hole from a flat, a [spigot or rabbet](https://3dwk.com/resources/spigot-rabbet-fit-notes-cnc-housings), or a datum slot so the pattern does not float in rotation. A pattern that must mate to a purchased motor flange should copy that flange’s PCD and clocking, not a “typical M6 circle.”

[Minimum hole-to-edge distance](https://3dwk.com/resources/minimum-hole-to-edge-distance-dfm-cnc-plates) still applies at the flange OD and toward any bore. Aluminum 6061 plate and billet $/kg planning bands sit in the common CNC aluminum range under **rates.v1.1** material tables; material cost is rarely the bolt-circle story—PCD, position scheme, and face flatness are.

True position of the pattern versus individual holes

Say whether the tolerance applies to the bolt-circle pattern as a group, to each hole from the datums, or to both. A cover that must oil-seal on a [face groove](https://3dwk.com/resources/face-groove-notes-cnc-rotary-seals) or a spigot often cares about the pattern and the face together; a simple lid may only need clearance holes on a loose PCD. Do not paste a tight true position on every hole when the real requirement is “the pattern lines up with the mate.”

Flange-face flatness and inspection traps

Calling “PCD as needed,” mixing clearance and tapped holes on one silent count, or applying a tight hole position while the flange face [flatness](https://3dwk.com/resources/flatness-vs-parallelism-callouts-cnc-plates) is left open, all force **needs_manual**. Default non-critical covers to a named PCD, hole count, and a general position; reserve a tight pattern position and a named face flatness for sealed or locating flanges. Related: [ISO 2768 general tolerances on CNC RFQs](https://3dwk.com/resources/iso-2768-general-tolerances-cnc-rfq), [what needs_manual means](https://3dwk.com/resources/what-needs-manual-means-preliminary-quote).

Illustration 1 shows an **Example part** 6061 housing with a labeled PCD 60, 6× Ø6.6 pattern and a named face flatness versus a silent “M6 bolt circle” outline on the same blank.

Example part walkthrough

**Example part:** Aluminum 6061-T6 housing flange ~Ø90 × 12 mm face, bolt circle PCD 60, 6× Ø6.6 clearance holes, first hole on datum B, true position of the pattern from A/B/C, flange-face flatness named, ISO 2768-m general on non-pattern dimensions, no hidden dowels in the hole count. With STEP + **PCD 60, 6× Ø6.6, FIRST HOLE ON B, PATTERN TP FROM A/B/C, FACE FLATNESS NAMED**, expect a usable automatic planning band on [quote-new.php](https://3dwk.com/quote-new.php). Same geometry with silent “standard 6× M6 flange, position as needed” often lands DFM notes or **needs_manual**—without inventing any customer PO.

Illustration 2 contrasts a vague RFQ (“bolt circle as needed”) versus a labeled PCD-count-clocking-position-flatness pack and the clearer estimate path.

What widens bands fastest

Unlabeled “standard flange” patterns, a PCD with no hole count or size, true position that does not say pattern versus each hole, and a tight pattern on a face whose flatness is silent. Quantity breaks help unit minutes but do not erase pattern-pack ambiguity—see [how quantity breaks change CNC unit cost](https://3dwk.com/resources/how-quantity-breaks-change-cnc-unit-cost) and [boss height and draft notes](https://3dwk.com/resources/boss-height-and-draft-notes-cnc-housings).

What to do next

Mark each flange with a **PCD, hole count and size, clocking, pattern versus hole position, and face flatness**, then upload on [quote-new.php](https://3dwk.com/quote-new.php). Packaging checklist: clearance versus tapped holes, any real dowels on their own line, and edge distance to the flange OD. Service pages: [CNC machining](https://3dwk.com/cnc-machining-service.php), [materials](https://3dwk.com/materials.php). Treat **rates.v1.1** min/mid/max as estimates, not invoices. If the UI shows **needs_manual**, answer the bolt-circle questions rather than forcing a fake price.

Common questions

Is a bolt circle just six holes on a diameter?

Only if you also name the PCD, the hole size, the clocking, and which position scheme applies. A diameter sketched in CAD is not a complete pattern pack.

Should true position apply to every hole or to the pattern?

It depends on the mate. If the cover only needs to bolt on, a pattern-level position with clearance holes is often enough. If each hole locates a stud or a tight insert, say so. Write which rule you mean.

How does flange-face flatness interact with the pattern?

A pattern can be in position and still leak or rock if the face is out of flat. Name face flatness on sealed or locating flanges, and keep it on the same sheet as the bolt circle.

Can I hide two dowels inside the bolt-circle count?

No. Dowels are a different family. Count them separately and use the dowel-location notes so the shop does not drill clearance holes where the pins belong.

Free DFM · 24h quote

Upload CAD → free DFM report

Email required. You get a link to a rule-based manufacturability checklist (not a formal engineering sign-off). Engineers still review pricing.

No CAD? Photo / description → 24h quote

Three fields only — we reply within 24 hours.

Next step

Questions about your design?

Upload CAD files and an engineer will review manufacturability with your quote.

Upload CAD