Design Guides

Grind-relief groove notes on CNC shafts

Grind-relief groove notes on CNC shafts: location, size, remain-or-remove, and rates.v1.1 estimate packaging—Example part only.

By 3DWK Engineering Team · · 6 min read

Example part Steel 1018 shaft map showing a labeled grind relief at the shoulder of journal B, width and depth cited, remaining on the finished part, kept clear of a ring groove
Illustration: 3DWK original diagram (typical values, not to scale).

The short answer

A **grind-relief groove** on a CNC shaft is not a [thread-relief or thread-runout](https://3dwk.com/resources/thread-relief-runout-notes-cnc-turned-parts), and it is not the same decision as [whether OD grinding is needed](https://3dwk.com/resources/when-is-od-grinding-needed-after-cnc-turning). It is also distinct from a [shoulder fillet versus undercut](https://3dwk.com/resources/shoulder-fillet-vs-undercut-cnc-turned-shafts) chosen only for stress. A usable callout says **which journal will be ground**, **where the relief sits** (usually at the shoulder), the **width and depth the drawing controls**, and whether the groove **remains on the finished part**. Silence, or a note that only says “leave a grind relief,” is what widens many [quote-new.php](https://3dwk.com/quote-new.php) **rates.v1.1** estimate bands—not the groove itself.

This guide is for buyers who already intend a later grind and need to **package the relief** so the wheel can finish the journal. Illustrations use an **Example part** only—not a customer shaft, and not a fabricated grind report. Sibling notes cover when grinding is justified; here we focus on **how to call the clearance groove** once that grind is on the drawing.

What grind-relief grooves mean for quoting

A **grind-relief pack** names the journal to be ground, the shoulder or face the relief undercuts, the groove size, and whether it is a manufacturing aid that stays. Writing “undercut for grind” or “relief as needed” is not enough. Process pages for common turned steel shafts ([CNC turning Steel 1018 aerospace](https://3dwk.com/en/cnc-turning/steel-1018/aerospace.html), [CNC turning Steel 1018 robotics](https://3dwk.com/en/cnc-turning/steel-1018/robotics.html), [CNC turning Steel 1018](https://3dwk.com/en/cnc-turning/steel-1018.html)) assume the pack is visible when lots mix as-turned journals, ground journals with a square shoulder, and ground journals with a named relief. Batch1 pages for 4140 combinations are not live, so this Example part is packaged on the live Steel 1018 turning siblings; treat the relief as a specified grind-clearance feature, not as a default undercut on every mild-steel shaft, and still name the actual steel grade if the part is an alloy.

Do not bury “grind relief as needed” inside a notes cloud. Put **GRIND RELIEF AT SHOULDER OF JOURNAL B, WIDTH AND DEPTH CITED, REMAINS ON FINISHED PART, KEEP CLEAR OF THE RING GROOVE** on the PDF and mirror it in RFQ text. If the journal is ground but a sharp corner is required with no undercut, say **NO GRIND RELIEF; SQUARE SHOULDER TO FACE C** and accept that the grind method must be planned around that corner. Background: [what files to send for a CNC quote](https://3dwk.com/resources/what-files-to-send-for-cnc-quote), [turned stainless shaft drawing guide](https://3dwk.com/resources/turned-stainless-shaft-drawing-guide).

Vague relief-as-needed RFQ versus labeled location-size-remain pack — Example part
Illustration: 3DWK original diagram (typical values, not to scale).

Location, size, and remain-versus-remove

Place the relief where the wheel would otherwise crash the shoulder—typically at the intersection of a ground diameter and a face. Cite width and depth, or the standard groove form you use; do not write only “standard grind relief.” If a fillet is required for stress and a relief is required for the wheel, say how those two features share the corner, rather than letting one note cancel the other.

If you control the groove size, write **those values on the PDF**. This guide does not invent a default relief width, a wheel-radius assumption, or a 3DWK-standard undercut. A thread relief is for die or thread-wheel runout, not for OD grinding of a bearing journal—keep those callouts on separate lines.

Keep-outs from grooves, threads, and seals

Give a minimum land between the relief and any [retaining-ring groove](https://3dwk.com/resources/retaining-ring-groove-notes-cnc-shafts), seal diameter, or thread so the undercut does not merge into a snap-ring seat or nick a lip-seal journal. If the relief would undercut a locating shoulder used as a datum, or if there is no room, shorten the journal, move the shoulder, or write that the grind must be done without a relief.

Tolerance and inspection traps

Calling “relief as needed,” leaving a grind note on journal B with a square corner and no statement either way, or dimensioning the relief tighter than the ground journal without a reason, all force **needs_manual**. Default a shaft that will not be ground to an explicit no-relief note; do not let a generic undercut appear because grinding was mentioned in a title block. Related: [what needs_manual means](https://3dwk.com/resources/what-needs-manual-means-preliminary-quote).

Illustration 1 shows an **Example part** Steel 1018 shaft with a labeled grind relief at the shoulder of journal B, width and depth cited, remaining on the finished part, and kept clear of a ring groove.

Example part walkthrough

**Example part:** Steel 1018 turned shaft, journal B to be ground later, grind relief required at the shoulder, width and depth on the PDF, groove remains, keep clear of the ring groove, no invented default wheel size or 3DWK relief recipe. With STEP + **GRIND RELIEF AT SHOULDER OF B, WIDTH / DEPTH CITED, REMAINS; KEEP CLEAR OF RING GROOVE**, expect a usable automatic planning band on [quote-new.php](https://3dwk.com/quote-new.php). Same geometry with silent “leave a grind relief as needed” often lands DFM notes or **needs_manual**—without inventing any customer grind ticket or a 3DWK-guaranteed wheel path.

Illustration 2 contrasts a vague RFQ (“relief as needed”) versus a labeled location-size-remain pack and the clearer estimate path.

What widens bands fastest

Unlabeled “as needed” reliefs, a grind callout with a square shoulder and no relief decision, keep-outs omitted next to ring grooves, and a relief size left to “shop standard.” Quantity breaks do not erase feature-pack ambiguity—see [how quantity breaks change CNC unit cost](https://3dwk.com/resources/how-quantity-breaks-change-cnc-unit-cost).

What to do next

Mark each relief with **which ground journal, where it sits, width and depth, remain-or-remove, and keep-outs**, then upload the CAD on [quote-new.php](https://3dwk.com/quote-new.php). Packaging checklist: this is not a thread relief, and it does not replace the separate decision of [when OD grinding is needed](https://3dwk.com/resources/when-is-od-grinding-needed-after-cnc-turning). Service pages: [CNC machining](https://3dwk.com/cnc-machining-service.php), [materials](https://3dwk.com/materials.php). Treat **rates.v1.1** min/mid/max as estimates, not invoices. If the UI shows **needs_manual**, answer the relief-pack questions rather than forcing a fake price.

Common questions

Is a grind-relief groove the same as a thread relief or a fillet undercut?

No. A thread relief is for thread runout. A fillet-versus-undercut note is often about stress at a shoulder. A grind relief is clearance for a later grinding wheel on a specified journal. Package each on its own line.

Do I have to add a relief if the journal will be ground?

Not automatically. If you need a sharp corner against a locating face, write **NO GRIND RELIEF** and accept the process implication. If the wheel needs room, cite the groove rather than leaving “relief as needed.”

Can the relief merge into a snap-ring groove?

Only if you say so. A default keep-out is safer. If the stack is short, change the layout or write the allowed exception on the PDF.

How should I inspect the relief?

Call out width and depth (or the form you cite) and confirm it does not break adjacent grooves or seal diameters. The ground journal still carries the tight diameter and finish; do not treat the relief as a substitute for those callouts.

Free DFM · 24h quote

Upload CAD → free DFM report

Email required. You get a link to a rule-based manufacturability checklist (not a formal engineering sign-off). Engineers still review pricing.

No CAD? Photo / description → 24h quote

Three fields only — we reply within 24 hours.

Next step

Questions about your design?

Upload CAD files and an engineer will review manufacturability with your quote.

Upload CAD