The short answer
On housing and bore RFQs, an **internal retaining-ring groove** is not the same as an [external ring groove on a shaft](https://3dwk.com/resources/retaining-ring-groove-notes-cnc-shafts), an [O-ring gland](https://3dwk.com/resources/o-ring-groove-callouts-cnc-housings), or a general undercut. An internal groove is cut in a bore so a circlip or retaining ring can sit behind a bearing, a bushing, or a cover. Silence on groove width, groove diameter (larger than the bore), location from a face, corner radii, and whether a lead-in chamfer is allowed for ring installation, is what widens many [quote-new.php](https://3dwk.com/quote-new.php) **rates.v1.1** estimate bands—not the extra seconds of an internal grooving tool alone.
This guide is for buyers packaging CNC bores where “standard internal circlip” is noted next to a bearing seat with no housing dimensions. Illustrations use an **Example part** only—not a customer housing. Sibling notes live in [press-fit versus slip-fit CNC bores](https://3dwk.com/resources/press-fit-vs-slip-fit-cnc-bores) and [when to call out undercuts](https://3dwk.com/resources/when-to-call-out-undercuts-on-cnc-rfq); here we focus on **internal-groove packaging** so estimators do not have to guess the width and groove Ø for a 20 mm bore, or whether the remaining wall outside the groove is thick enough.
What an internal retaining-ring groove means for quoting
An **internal ring-groove pack** names groove width, groove diameter, location from a datum face, maximum corner radius (or a sharp-corner note), and any installation chamfer at the bore mouth. It is not an O-ring gland: a gland is sized for squeeze and often wants a radius in the bottom, while a ring groove is sized for the ring’s thickness and a nearly square seat. A general “standard snap ring for this bore” cloud does not give the grooving tool a width or a diameter. Process pages for aluminum milling and turning ([CNC 3-axis Al 6061 automation](https://3dwk.com/en/cnc-3axis/al-6061/automation.html), [CNC turning Al 6061 automation](https://3dwk.com/en/cnc-turning/al-6061/automation.html), [CNC 3-axis Al 6061](https://3dwk.com/en/cnc-3axis/al-6061.html)) assume internal grooves are dimensioned when lots mix bearing bores with ring retention.
Do not bury “internal circlip as needed” inside a notes cloud. Put **INTERNAL RING GROOVE: WIDTH 1.15, GROOVE Ø21.1, 6.0 FROM FACE A, CORNER R 0.2 MAX, LEAD-IN CHAMFER 0.3 × 45° AT BORE MOUTH** on the PDF and mirror it in RFQ text. Background: [DFM checklist before an online CNC quote](https://3dwk.com/resources/dfm-checklist-before-online-cnc-quote), [what files to send for a CNC quote](https://3dwk.com/resources/what-files-to-send-for-cnc-quote), [reaming versus boring](https://3dwk.com/resources/reaming-vs-boring-cnc-hole-size).
Width, groove diameter, and remaining wall
Name width and groove diameter explicitly, preferably from the ring maker’s housing dimensions for the ring you will buy—do not assume the shop will pick a “standard” for a 20 mm bore. Check the remaining wall outside the groove so a thin housing does not become a paper ring at the groove diameter. [Minimum wall notes](https://3dwk.com/resources/minimum-wall-cnc-vs-slm-for-buyers) and [minimum hole-to-edge distance](https://3dwk.com/resources/minimum-hole-to-edge-distance-dfm-cnc-plates) are the same idea on a different feature: leave metal around the groove.
Aluminum 6061 plate and billet $/kg planning bands sit in the common CNC aluminum range under **rates.v1.1** material tables; material cost is rarely the groove story—internal tool access, width-to-depth ratio, and location to a bearing seat are.
Location, corner radius, and installation chamfer
Locate the groove from a named face so the ring actually traps the bearing or cover you intend. A corner radius that is larger than the ring can sit on will let the ring rock; a dead-sharp internal corner may need a special tool. A short lead-in chamfer at the bore mouth helps installation but must not eat the bearing land. This is a different problem from an [external shaft groove](https://3dwk.com/resources/retaining-ring-groove-notes-cnc-shafts): the tool is inside the bore, and access through a long or stepped hole should be stated.
Tolerance and inspection traps
Calling “standard internal circlip,” mixing O-ring gland proportions with a ring groove, or asking for 100% groove-width photos on every piece, all force **needs_manual**. Default non-critical covers to a written width/Ø/location pack, and put a tight width only where the ring must be captive without play. Related: [ISO 2768 general tolerances on CNC RFQs](https://3dwk.com/resources/iso-2768-general-tolerances-cnc-rfq), [circularity versus cylindricity](https://3dwk.com/resources/circularity-vs-cylindricity-cnc-shafts).
Illustration 1 shows an **Example part** housing with a labeled internal ring groove behind a Ø20 bearing bore versus a light cover groove with a confirmed width only.
Example part walkthrough
**Example part:** Aluminum 6061-T6 housing ~60 × 40 × 25 mm, Ø20 bearing bore, internal ring groove width 1.15 mm, groove Ø21.1 mm, 6.0 mm from face A, corner R 0.2 mm max, 0.3 × 45° lead-in at the bore mouth, ISO 2768-m general. With STEP + **INT. RING GROOVE W1.15 / Ø21.1 / 6.0 FROM A; R0.2 MAX; LEAD-IN 0.3×45°**, expect a usable automatic planning band on [quote-new.php](https://3dwk.com/quote-new.php). Same geometry with silent “standard internal snap ring for 20 mm bore” often lands DFM notes or **needs_manual**—without inventing any customer PO.
Illustration 2 contrasts a vague RFQ (“internal circlip standard”) versus a labeled width-diameter-location pack and the clearer estimate path.
What widens bands fastest
Unlabeled “standard circlip,” groove Ø left implicit, remaining wall ignored on a thin housing, and O-ring-style radii drawn on a ring seat. Quantity breaks help unit minutes but do not erase groove-pack ambiguity—see [how quantity breaks change CNC unit cost](https://3dwk.com/resources/how-quantity-breaks-change-cnc-unit-cost) and [what needs_manual means](https://3dwk.com/resources/what-needs-manual-means-preliminary-quote).
What to do next
Mark each internal ring groove with **width, groove Ø, location, and corner/lead-in notes**, then upload on [quote-new.php](https://3dwk.com/quote-new.php). Service pages: [CNC machining](https://3dwk.com/cnc-machining-service.php), [materials](https://3dwk.com/materials.php). Treat **rates.v1.1** min/mid/max as estimates, not invoices. If the UI shows **needs_manual**, answer the groove questions rather than forcing a fake price.
Common questions
Is an internal ring groove the same as an O-ring gland?
No. An O-ring gland is sized for squeeze and often uses a radiused bottom. A retaining-ring groove is sized for a specific ring thickness and wants a seat the ring can lock against. Copying gland proportions onto a circlip usually makes a loose or un-installable ring.
Can I just write “standard internal ring for Ø20”?
Only if you also attach the housing dimensions you will buy to (width, groove Ø, location). “Standard” is not a size. Different ring series for the same nominal bore do not share one groove.
Does the groove need a lead-in chamfer?
A short chamfer at the bore mouth often helps the ring enter. It should not cut into the bearing land or the groove seat. If the bearing is pressed past that mouth, say so, and keep the chamfer modest.
What if the groove sits deep inside a long bore?
Say the depth and whether a necked grooving tool must reach past a step. A groove that is easy on a short bore can become a special tool or a second setup in a deep pocket—write the access, do not leave it to a notes cloud.
