Design Guides

Set-screw flat and dimple notes on CNC shafts

Set-screw flat and dimple notes on CNC shafts: location, form, size, and rates.v1.1 estimate packaging—Example part only.

By 3DWK Engineering Team · · 6 min read

Example part SS 304 shaft map showing labeled set-screw flat on journal B, axial station cited, width and remaining height cited, no dimple unless called out, kept clear of journal A and a ring groove
Illustration: 3DWK original diagram (typical values, not to scale).

The short answer

A **set-screw flat** or a **set-screw dimple** on a CNC shaft is not a [wrench flat](https://3dwk.com/resources/wrench-flat-notes-cnc-turned-shafts), not a [D-flat or double-D](https://3dwk.com/resources/d-flat-vs-double-d-notes-cnc-shafts), and not a [keyway](https://3dwk.com/resources/keyway-callouts-on-cnc-turned-shafts) or [Woodruff seat](https://3dwk.com/resources/woodruff-key-seat-notes-cnc-shafts). A usable callout says **which diameter**, the **axial and angular location**, whether the feature is a **milled flat, a dimple, or both**, the **size the drawing actually controls** (flat width or remaining height, dimple form and depth), and **keep-outs** from journals, grooves, and threads. Silence, or a note that only says “add a set-screw flat,” is what widens many [quote-new.php](https://3dwk.com/quote-new.php) **rates.v1.1** estimate bands—not the milling minutes alone.

This guide is for buyers packaging turned or milled shafts that a hub, collar, or coupling will clamp with a set screw. Illustrations use an **Example part** only—not a customer shaft, and not a fabricated assembly photo. Sibling notes cover wrenching pads and D-flats; here we focus on **packaging a local bearing patch for a set screw**.

What set-screw flats and dimples mean for quoting

A **set-screw-flat pack** names the journal, the axial station, any clocking relative to another feature, the form (flat versus dimple), and the size that must be inspected. Writing “flat for set screw” or “spot the shaft” is not enough. Process pages for common turned shafts ([CNC turning SS 304 automation](https://3dwk.com/en/cnc-turning/ss-304/automation.html), [CNC turning SS 304](https://3dwk.com/en/cnc-turning/ss-304.html), [CNC turning SS 304 robotics](https://3dwk.com/en/cnc-turning/ss-304/robotics.html)) assume that pack is visible when lots mix plain journals, wrench flats, and local set-screw patches.

Do not bury “set-screw flat as needed” inside a notes cloud. Put **SET-SCREW FLAT ON ØB, AXIAL STATION CITED, WIDTH AND REMAINING HEIGHT CITED, DIMPLE FORM AND DEPTH CITED IF REQUIRED, KEEP CLEAR OF JOURNAL A AND THE RETAINING-RING GROOVE** on the PDF and mirror it in RFQ text. If the shaft must stay a full cylinder—no flat and no dimple—say **NO SET-SCREW FLAT / NO DIMPLE** so the shop does not invent a pad. Background: [what files to send for a CNC quote](https://3dwk.com/resources/what-files-to-send-for-cnc-quote), [turned stainless shaft drawing guide](https://3dwk.com/resources/turned-stainless-shaft-drawing-guide).

Vague flat-for-set-screw RFQ versus labeled location-form-size pack — Example part
Illustration: 3DWK original diagram (typical values, not to scale).

Location, form, and size

Name the diameter the screw will bear on, the distance from a datum or shoulder, and the angular location if the flat must line up with a keyway, a cross-hole, or a mating hub. A milled flat is a local chord; a dimple is a conical or spherical seat for a pointed or cup-point screw. They are not interchangeable, and a drawing that says only “spot for set screw” leaves both the tool and the inspection method open.

If you control remaining height, flat width, or dimple depth, write **those values and the standard or method you use on the PDF**. This guide does not invent a default flat width, a leftover diameter, a dimple included angle, or a 3DWK-standard set-screw patch. [Knurling](https://3dwk.com/resources/knurling-on-cnc-turned-shafts) and [center holes](https://3dwk.com/resources/center-hole-notes-cnc-turned-shafts) are separate features; do not let a set-screw note replace them.

Keep-outs and mating hardware

Give a minimum land to adjacent undercuts, [retaining-ring grooves](https://3dwk.com/resources/retaining-ring-groove-notes-cnc-shafts), threads, and bearing journals so the mill or dimple tool does not break a shoulder or nick a seal diameter. If the hub already exists, say whether the shaft patch must match a known screw size and location—but still put the shaft dimensions on the shaft PDF rather than “match the collar.” A through-dimple that breaks the far side of a thin wall is a different RFQ from a shallow seat that stays inside the journal.

Tolerance and inspection traps

Calling “set-screw flat as needed,” asking for a “standard dimple,” or leaving clocking silent when the hub is already clocked, all force **needs_manual**. Default a shaft that only needs a smooth journal to an explicit no-flat note; do not let a generic “for set screw” appear as an implied mill step. Related: [what needs_manual means](https://3dwk.com/resources/what-needs-manual-means-preliminary-quote).

Illustration 1 shows an **Example part** SS 304 shaft with a labeled set-screw flat on ØB, axial station cited, width and remaining height cited, an optional dimple called out only if required, and keep-outs from journal A and a ring groove.

Example part walkthrough

**Example part:** SS 304 turned shaft, set-screw flat required on ØB at a cited station, width and remaining height on the PDF, no dimple unless a second callout names form and depth, keep clear of journal A and the ring groove, no invented default screw size or 3DWK patch recipe. With STEP + **SET-SCREW FLAT ON ØB, STATION / WIDTH / REMAINING HEIGHT CITED; NO DIMPLE; KEEP CLEAR OF A AND THE GROOVE**, expect a usable automatic planning band on [quote-new.php](https://3dwk.com/quote-new.php). Same geometry with silent “add a set-screw flat as needed” often lands DFM notes or **needs_manual**—without inventing any customer collar, screw lot, or a 3DWK-guaranteed clamp torque.

Illustration 2 contrasts a vague RFQ (“flat for set screw”) versus a labeled location-form-size pack and the clearer estimate path.

What widens bands fastest

Unlabeled “as needed” flats, a dimple note with no form or depth, clocking left silent against a keyed hub, and keep-outs omitted next to grooves or threads. Quantity breaks do not erase feature-pack ambiguity—see [how quantity breaks change CNC unit cost](https://3dwk.com/resources/how-quantity-breaks-change-cnc-unit-cost).

What to do next

Mark each patch with **location, form (flat, dimple, or both), size, clocking if required, and keep-outs**, then upload the CAD on [quote-new.php](https://3dwk.com/quote-new.php). Packaging checklist: this is not a wrench flat, not a D-flat, and not a keyway. Service pages: [CNC machining](https://3dwk.com/cnc-machining-service.php), [materials](https://3dwk.com/materials.php). Treat **rates.v1.1** min/mid/max as estimates, not invoices. If the UI shows **needs_manual**, answer the set-screw-patch questions rather than forcing a fake price.

Common questions

Is a set-screw flat the same as a wrench flat or a D-flat?

No. A wrench flat is for turning or holding the shaft; a D-flat or double-D is usually a drive or orientation feature along a length. A set-screw flat or dimple is a local bearing patch for a screw in a hub or collar. Package each feature on its own line.

Do I have to name a dimple if I only want a milled flat?

No. Write the flat and add **NO DIMPLE** if a pointed screw seat is not allowed. If you do want a dimple, cite form and depth; “spot for set screw” is not a size.

Can the flat break into a ring groove or a thread?

Only if you say so. A default keep-out is safer: give a minimum land to the groove, the thread, and any seal journal. If a short stack has no room, write the allowed exception on the PDF.

How should I inspect the patch?

Call out the controlled size (remaining height or width for a flat; form and depth for a dimple), the axial station, and any angular location. Do not leave “for set screw” as the only acceptance note.

Free DFM · 24h quote

Upload CAD → free DFM report

Email required. You get a link to a rule-based manufacturability checklist (not a formal engineering sign-off). Engineers still review pricing.

No CAD? Photo / description → 24h quote

Three fields only — we reply within 24 hours.

Next step

Questions about your design?

Upload CAD files and an engineer will review manufacturability with your quote.

Upload CAD