Design Guides

Spring-pin hole notes for CNC parts

Spring-pin hole notes for CNC parts: standard, size, fit class, keep-outs and rates.v1.1 estimate packaging—Example part only.

By 3DWK Engineering Team · · 5 min read

Example part Al 6061 plate map showing a labeled spring-pin hole, pin standard cited, hole size and class cited, interference or clearance cited, keep-outs from an edge and a tap
Illustration: 3DWK original diagram (typical values, not to scale).

The short answer

A **spring-pin hole** on a CNC part is not a [dowel-pin hole](https://3dwk.com/resources/dowel-pin-hole-location-dfm-cnc), not a [press-fit pin or bushing](https://3dwk.com/resources/press-fit-pins-bushings-cnc-housings) seat, and not a generic [press-fit versus slip-fit bore](https://3dwk.com/resources/press-fit-vs-slip-fit-cnc-bores). A usable callout says **the pin standard**, the **hole size and tolerance class you actually use**, whether the fit is **interference or clearance**, the **location and depth**, and **keep-outs** from edges, threads, and other holes. Silence, or a note that only says “add a spring-pin hole,” is what widens many [quote-new.php](https://3dwk.com/quote-new.php) **rates.v1.1** estimate bands—not the drill minutes alone.

This guide is for buyers packaging plates, hubs, or levers that locate or retain with a slotted or coiled spring pin. Illustrations use an **Example part** only—not a customer plate, and not a fabricated pin or assembly photo. Sibling notes cover dowels and press-fit bushings; here we focus on **packaging a spring-pin hole**, including the standard, hole class, and fit the buyer actually uses.

What spring-pin holes mean for quoting

A **spring-pin-hole pack** names the pin family or standard, the hole size and class the drawing controls, interference versus clearance, location and depth (through or stopped), and keep-outs. Writing “hole for spring pin” or “standard roll-pin hole” is not enough. Process pages for common aluminum parts ([CNC 3-axis Al 6061 automation](https://3dwk.com/en/cnc-3axis/al-6061/automation.html), [CNC turning Al 6061 automation](https://3dwk.com/en/cnc-turning/al-6061/automation.html), [CNC 3-axis Al 6061](https://3dwk.com/en/cnc-3axis/al-6061.html)) assume that pack is visible when lots mix clearance holes, dowel holes, and spring-pin holes.

Do not bury “spring-pin hole as needed” inside a notes cloud. Put **SPRING-PIN HOLE, PIN STANDARD CITED, HOLE SIZE AND TOLERANCE CLASS CITED, INTERFERENCE OR CLEARANCE CITED, LOCATION AND DEPTH CITED, KEEP CLEAR OF THE EDGE AND ANY TAPPED HOLE** on the PDF and mirror it in RFQ text. If the part must have no spring-pin hole, say **NO SPRING-PIN HOLE** so the shop does not invent a drilled size. Background: [what files to send for a CNC quote](https://3dwk.com/resources/what-files-to-send-for-cnc-quote), [dowel-pin hole location DFM](https://3dwk.com/resources/dowel-pin-hole-location-dfm-cnc).

Vague roll-pin-hole RFQ versus labeled standard-size-fit pack — Example part
Illustration: 3DWK original diagram (typical values, not to scale).

Pin standard, hole size, and fit

Name the pin type (slotted, coiled, or another family you actually use) and write the **document and size designation on the PDF**. Then write the hole size and tolerance class the shop must make—not “drill for a spring pin.” Interference versus clearance is part of that pack: a recommended hole from your pin standard is not the same as a precision dowel ream, and it is not a loose clearance hole unless you say so. If a coating or anodize will change the finished hole, say whether the class applies before or after that finish.

This guide does not invent a default hole diameter, a tolerance class, an interference value, or a 3DWK-standard spring-pin hole. A dowel hole is for location; a press-fit bushing is a different insert. Do not let a spring-pin note replace those features.

Location, depth, and keep-outs

Give position from a datum, and say whether the hole is through or stopped at a cited depth. A through hole that exits a thin wall or a cosmetic face is a different RFQ from a stopped hole. Keep a minimum land to edges, [tapped holes](https://3dwk.com/resources/dowel-pin-hole-location-dfm-cnc), and adjacent bores so the pin does not break out or distort a precision diameter. If the mating part already exists, still put the hole size and class on this PDF rather than “match the pin.” A pattern of two or more spring-pin holes also needs position between holes, not only a single size callout.

Tolerance and inspection traps

Calling “spring-pin hole as needed,” asking for a “standard roll-pin hole” with no document or size, or leaving interference versus clearance silent, all force **needs_manual**. Default a plate that only needs a clearance hole to an explicit no-spring-pin note; do not let a generic “for roll pin” appear as an implied undersize drill. Alignment pins used only for assembly, versus pins that also take shear, should say so on the same pack. Related: [what needs_manual means](https://3dwk.com/resources/what-needs-manual-means-preliminary-quote).

Illustration 1 shows an **Example part** Al 6061 plate with a labeled spring-pin hole, pin standard cited by the buyer, hole size and class cited, interference or clearance cited, and keep-outs from an edge and a tapped hole.

Example part walkthrough

**Example part:** Al 6061 plate, spring-pin hole required, buyer pin standard and size cited, hole size and tolerance class on the PDF, interference or clearance cited, location and through-or-stopped depth cited, keep clear of the edge and any tapped hole, no invented default hole size or 3DWK pin recipe. With STEP + **SPRING-PIN HOLE; STANDARD / SIZE / CLASS CITED; INTERFERENCE OR CLEARANCE CITED; KEEP CLEAR OF THE EDGE AND TAP**, expect a usable automatic planning band on [quote-new.php](https://3dwk.com/quote-new.php). Same geometry with silent “add a spring-pin hole as needed” often lands DFM notes or **needs_manual**—without inventing any customer pin lot, or a 3DWK-guaranteed retention load.

Illustration 2 contrasts a vague RFQ (“hole for roll pin”) versus a labeled standard-size-fit pack and the clearer estimate path.

What widens bands fastest

Unlabeled “as needed” spring-pin holes, a “standard roll-pin hole” note with no document or class, fit type left silent, and keep-outs omitted next to edges or taps. Quantity breaks do not erase feature-pack ambiguity—see [how quantity breaks change CNC unit cost](https://3dwk.com/resources/how-quantity-breaks-change-cnc-unit-cost).

What to do next

Mark each hole with **the pin standard, hole size and class, interference or clearance, location and depth, and keep-outs**, then upload the CAD on [quote-new.php](https://3dwk.com/quote-new.php). Packaging checklist: this is not a dowel hole, not a press-fit bushing, and not a generic slip-fit bore. Service pages: [CNC machining](https://3dwk.com/cnc-machining-service.php), [materials](https://3dwk.com/materials.php). Treat **rates.v1.1** min/mid/max as estimates, not invoices. If the UI shows **needs_manual**, answer the spring-pin-hole questions rather than forcing a fake price.

Common questions

Is a spring-pin hole the same as a dowel hole or a press-fit bushing?

No. A dowel hole is usually a precision location ream. A press-fit bushing is an inserted wear or guide element. A spring-pin hole follows the pin standard and the hole class you cite. Package each feature on its own line.

Can 3DWK just use a standard hole size?

Cite the pin standard and the hole size or class you need on the PDF. This guide does not invent a default diameter, a fit, or a drill size as a 3DWK guarantee.

Can the hole break out at an edge or into a tap?

Only if you say so. A default keep-out is safer: give a minimum land to the edge, the tapped hole, and any precision bore. If a short stack has no room, write the allowed exception on the PDF.

How should I inspect the hole?

Call out the controlled size and class, through or stopped depth, and position. Do not leave “for spring pin” as the only acceptance note.

Free DFM · 24h quote

Upload CAD → free DFM report

Email required. You get a link to a rule-based manufacturability checklist (not a formal engineering sign-off). Engineers still review pricing.

No CAD? Photo / description → 24h quote

Three fields only — we reply within 24 hours.

Next step

Questions about your design?

Upload CAD files and an engineer will review manufacturability with your quote.

Upload CAD