Start with the substitution, not the alloy number
A shop or a buyer often writes “303 or 304” on a stainless RFQ because 303 is the free-machining cousin of 304: it typically cuts with shorter chips and less work hardening on a busy turned or milled bar part. That swap is only safe when the part can accept what the sulfur addition gives up.
Specify 303 when the component is heavily machined from bar, will not be welded, and the service environment is already mild enough that 304 would have been acceptable for corrosion. Stay with 304, 316, or 17-4PH when the print already named that grade for a reason — a weld, a chloride or chemical duty, a hardness or strength callout, or a sanitary or pressure requirement. Put the grade, the specification you actually buy to, and a clear yes or no on substitutions in the PDF you send with the STEP through quote-new.php, so the estimate is priced on the alloy that will ship.
What 303 actually changes
303 (typically UNS S30300, and often purchased as bar to a free-machining stainless specification such as ASTM A582) is an austenitic stainless with sulfur added to form manganese sulfide inclusions. Those inclusions help the chip break and the tool cut, which is why the grade shows up on fittings, connectors, bushings, and other hardware with a lot of turning, drilling, and threading. The same inclusions are why 303 is a different corrosion and weld path from 304, not a silent equivalent.
| Grade | Typical role on a CNC RFQ | Typical machining behavior | Typically a poor choice when |
|---|---|---|---|
| 303 | Free-machining austenitic for heavily cut bar hardware | Chips break more readily than 304; less tendency to smear and work-harden | The part will be welded, or the environment already justified 316 or a hardening grade |
| 304 | General-purpose austenitic when corrosion and occasional fabrication both matter | Stringy chips and work hardening are normal; still the default for many welded or sanitary parts | You only needed free-machining and already accepted 303's limits in writing |
| 316 | Molybdenum-bearing austenitic for chlorides and many chemical duties | Similar machining family to 304, not a free-machining grade | The duty that drove 316 is still on the drawing |
| 17-4PH | Precipitation-hardening stainless when strength or a hardness callout is the point | Machined in a defined condition, then aged if the print says so | You only wanted easier cutting; 17-4 is not a 303 substitute |
Stainless steel 304 vs 316 vs 17-4PH: matching the grade to the environment is the companion that walks those three grades. This page answers a narrower question: when the free-machining 303 variant is the right CNC call, and when a suggestion to “just use 303” should be refused. When to specify passivation after CNC stainless and passivation vs electropolishing for stainless still apply after the grade is chosen. Electropolish is discussed more often on 304 and 316; it does not turn 303 into 316.
303 is a specified grade, not a machining shortcut. A verbal “303 is fine” does not replace a drawing revision.
When 303 is the right grade
Heavily machined fittings and hardware
Call for 303 when the part is a connector, fitting, bushing, coupling nut, standoff, or similar bar component whose cycle time is dominated by turning, drilling, tapping, or thread milling, and the surrounding environment is not why you chose stainless in the first place. On those jobs, 304's stringy chips and work-hardening are a real process cost, and 303 is a standard way to buy a more cooperative austenitic without leaving the alloy family. Thread milling vs tapping for CNC buyers and designing threads and tapped holes for machined parts still decide how the thread is cut; the grade decides how the material behaves while it is cut.
Bar parts that will not be welded
Call for 303 when the finished part is used as-machined or with a mechanical joint — a clamp, a locational shaft, a knob, or a block that bolts to something else — and nobody intends to weld or braze the piece later. Sulfur-bearing free-machining grades are generally not the stainless you pick for a welded bracket or a fabricated housing. If a later weld is even a possibility, stay on 304 or 316 and say so on the RFQ. When should I split a CNC part into two pieces? is the question to ask if a weld is being used only to avoid a difficult one-piece machining path.
Mild service where 304 would already have been enough
Call for 303 when you would have accepted 304 for corrosion, and you are changing grade only to improve machining, not to chase a harsher environment. Indoor equipment and general industrial hardware often fall in this band when the drawing does not already impose a chloride, sanitary, or chemical note. If 316 was chosen because of chlorides, seawater, process chemicals, or a customer specification, 303 is not a cost-down. If 17-4PH was chosen because of strength or a hardness note, 303 will not meet that function (see 17-4PH H900 vs H1025: what buyers choose, and tolerances for CNC machined 17-4PH).
When to stay with 304, 316, or 17-4PH
Keep 304 when the part may be welded or needs the general corrosion behavior the print already assumed, including many sanitary and fabricated housings. Keep 316 when the environment or the specification that drove molybdenum is still in force. Keep 17-4PH when the drawing calls for a precipitation-hardening condition, a hardness range, or a strength level 303 cannot provide. Heat-treat notes belong on 17-4 and on heat-treatable steels, not as a way to “upgrade” 303 (see when to specify heat treat after CNC and heat treating steel after CNC machining).
Also stay off 303 when a standard, a customer list, or a previous qualification already froze 304 or 316, even if a shop can machine 303 faster. A first article qualified on one grade is not automatically qualified on another. When should I request mill certs with CNC parts? still applies: if you need a certificate, name the grade and the specification you expect to see on it, not a family word such as “stainless.” An early prototype cut from 303 to save time does not authorize a silent grade change on the production drawing (see prototype vs production CNC quotes). If the two will differ, write both grades on the RFQ.
What belongs on the drawing and the RFQ
Name the grade as a grade, not as a hope. “Stainless” or “SS” is not a specification. If 303 is the intent, write 303 or UNS S30300, and add the product specification you actually buy to — for bar, a free-machining stainless bar specification such as ASTM A582 is a typical reference. If you will accept 304 as an alternate, say “303, 304 acceptable” only when you have already accepted 304's machining behavior and 303's corrosion and weld limits. If you will not accept a swap, write “no material substitution without written approval.”
Add the stock form and condition, because bar, plate, or a cut-off can machine and inspect differently. If passivation is required after machining, say so and point to the note you already use (see when to specify passivation after CNC stainless). Do not skip passivation on the theory that “it is already stainless,” and do not treat electropolish as a cure for choosing the wrong grade (see when to specify electropolish after CNC stainless). If a later weld, braze, or pressure boundary is forbidden or required, write that sentence on the same sheet as the grade.
If the part is a turned shaft, the shaft-drawing companion (turned stainless steel shafts: tolerances, fits and finishes on the drawing) still controls fits, runout, and finish; this page only decides whether 303 is an acceptable material for that shaft. Surface roughness Ra for machined parts should stay a measurable band, not a promise that 303 will “look better.”
- Grade and specification: 303 / UNS S30300, plus the bar or product spec you buy to
- Substitution rule: allowed alternates, or no substitution without written approval
- Form and condition of the stock
- Weld, braze, or fabrication limits, if any apply
- Passivation or other finish, named rather than implied
- Certificate requirement, if you need a mill cert against the same grade
- A drawing PDF that matches the STEP, uploaded together through quote-new.php (see what files to send for a CNC quote and the DFM checklist before an online CNC quote)
Errors that look cheap on the quote
The most common error is a silent 304-to-303 swap after the PO, justified only by cycle time. That change can be reasonable, but it is a revision: it alters corrosion behavior, weldability, and often the certificate. Treat it like any other material change, and do not bury it in a shop traveler the buyer never sees.
The second error is using 303 on a part that will be welded, or that sits in the chloride or chemical duty that justified 316. Easier chips do not offset a crevice or a process-fluid note already on the print. The third is asking 303 to carry a 17-4PH hardness or strength callout. The fourth is omitting passivation or inspection notes because the word “stainless” felt sufficient, then finding at incoming inspection that the certificate, the finish, or the marking does not match the drawing. A fifth is writing “303 / 304 / 316, shop's choice,” which leaves the corrosion path, the weld path, and the certificate to whoever is programming the job. If more than one grade is acceptable, list those grades and the function they must still meet.
A last check before you upload
On quote-new.php, check that each item is on the drawing:
- The grade is a real designation, not the word “stainless”
- 303 is used only where welding is not required and the environment did not already demand 316 or 17-4PH
- Allowed substitutions are written, or clearly forbidden
- Passivation, marking, and certificate needs are stated if you require them
- The STEP and the PDF name the same material
If you are still choosing among 304, 316, and 17-4PH rather than asking whether 303 is allowed, start with the three-grade companion article, then come back to this page. If cost or lead time is the pressure behind the swap, read what drives CNC machining cost and what affects CNC machining lead time so you are not using a grade change to solve a quantity, setup, or finish problem.
Close the RFQ with a clear grade
Specify 303 stainless for CNC parts when you need a free-machining austenitic for heavily cut bar hardware, the part will not be welded, and the service environment would already have accepted 304. Do not use 303 as a quiet substitute for 316 or 17-4PH, and do not let a verbal machining preference overwrite a qualified grade. Write the designation, the specification, the substitution rule, and the finish notes on the PDF, then send both files through quote-new.php so the quote and the certificate point at the same alloy.
