Design Guides

Woodruff-key seat notes on CNC shafts

Woodruff-key seat notes on CNC shafts: seat width, diameter, depth and keep-outs, and rates.v1.1 estimate packaging—Example part only.

By 3DWK Engineering Team · · 5 min read

Example part SS 304 shaft map showing a labeled Woodruff seat width 5, cutter diameter 16.5, depth from the OD, 12 from datum A, and keep-outs at journal B and the M10 thread
Illustration: 3DWK original diagram (typical values, not to scale).

The short answer

A **Woodruff-key seat** (the half-moon / segmental pocket cut across a shaft) is not a rectangular parallel keyway with the corners filled in, and it is not a license to write only “Woodruff as needed.” A usable callout names the **seat width**, the **cutter diameter** (or the key standard and size that fix that diameter), the **depth** from the shaft outside diameter or a remaining height, the **axial location**, and the **keep-outs** around adjacent journals, undercuts, snap-ring grooves, or threads. Silence on diameter versus depth is what widens many [quote-new.php](https://3dwk.com/quote-new.php) **rates.v1.1** estimate bands—not the extra minutes of a Woodruff cutter alone.

This guide is for buyers packaging turned stainless shafts where a hub or coupling is timed with a half-moon key, but the drawing says only “Woodruff key” or reuses a rectangular [keyway callout](https://3dwk.com/resources/keyway-callouts-on-cnc-turned-shafts). Illustrations use an **Example part** only—not a customer shaft. Sibling notes live in that keyway guide and in [D-flat versus double-D notes](https://3dwk.com/resources/d-flat-vs-double-d-notes-cnc-shafts) and [wrench-flat notes](https://3dwk.com/resources/wrench-flat-notes-cnc-turned-shafts); here we focus on **Woodruff seat packaging**, not on parallel keyways, wrench flats, or D-cuts.

What Woodruff-key seats mean for quoting

A **Woodruff seat** is a circular-segment groove. Width, cutter diameter, and depth travel together; changing one without the others changes the key fit and the remaining wall under the seat. Writing “standard Woodruff” or “half-moon for hub” is not enough. Process pages for stainless turning ([CNC turning SS 304 automation](https://3dwk.com/en/cnc-turning/ss-304/automation.html), [CNC turning SS 304](https://3dwk.com/en/cnc-turning/ss-304.html), [CNC 3-axis SS 304 automation](https://3dwk.com/en/cnc-3axis/ss-304/automation.html)) assume the seat family is visible when lots mix keyways, D-flats, and Woodruff seats on the same shaft family.

Do not bury “Woodruff as needed” inside a notes cloud. Put **WOODRUFF SEAT A: WIDTH 5, CUTTER Ø16.5, DEPTH FROM OD NAMED, 12 FROM DATUM A, KEEP JOURNAL B AND M10** on the PDF and mirror it in RFQ text. If you work from a named key standard (for example a buyer-cited ANSI or ISO Woodruff series), write the **standard and size** plus the seat dimensions the shop must cut—do not assume the cutter diameter is obvious from the word “Woodruff” alone. Background: [turned stainless shaft drawing guide](https://3dwk.com/resources/turned-stainless-shaft-drawing-guide), [what files to send for a CNC quote](https://3dwk.com/resources/what-files-to-send-for-cnc-quote), [DFM checklist before an online CNC quote](https://3dwk.com/resources/dfm-checklist-before-online-cnc-quote).

Vague standard-Woodruff RFQ versus labeled width-diameter-depth-keep-out pack — Example part
Illustration: 3DWK original diagram (typical values, not to scale).

Width, cutter diameter, and depth

Name the seat width as a machined dimension, not only as a key commodity size. Name the cutter diameter or the radius of the segmental seat, because depth alone does not fix the shape. Depth is usually taken from the shaft OD, or given as a remaining height over the seat bottom; pick one and stay consistent. A seat that is deep relative to a slender shaft changes stiffness and can break into a center hole or an adjacent [retaining-ring groove](https://3dwk.com/resources/retaining-ring-groove-notes-cnc-shafts).

Stainless Steel 304 bar $/kg planning bands sit in the common CNC stainless range under **rates.v1.1** material tables; material cost is rarely the Woodruff-seat story—cutter diameter, depth, and keep-outs are.

Location, keep-outs, and runout

Give the axial start or center of the seat from a named datum, and say whether the seat may break a shoulder fillet or must keep a minimum land. Keep-outs should call out the journal, the thread runout, and any undercut so the cutter does not steal a bearing land. [Circularity versus cylindricity](https://3dwk.com/resources/circularity-vs-cylindricity-cnc-shafts) and [concentricity versus runout](https://3dwk.com/resources/concentricity-vs-runout-callouts-cnc-shafts) belong on the same sheet when the seat sits between two journals that actually run in bores.

Tolerance and inspection traps

Calling “Woodruff as needed,” pasting a rectangular keyway note onto a half-moon seat, or naming a width with no cutter diameter or depth, all force **needs_manual**. Default the seat to a named width, diameter, depth, and axial location, and reserve tight positional or runout controls for the journals that actually locate the assembly. Related: [ISO 2768 general tolerances on CNC RFQs](https://3dwk.com/resources/iso-2768-general-tolerances-cnc-rfq), [what needs_manual means](https://3dwk.com/resources/what-needs-manual-means-preliminary-quote).

Illustration 1 shows an **Example part** Ø20 stainless shaft with a labeled 5 mm wide, Ø16.5 cutter Woodruff seat versus a silent “standard Woodruff” outline on the same blank.

Example part walkthrough

**Example part:** Stainless Steel 304 shaft, parent Ø20, Woodruff seat width 5, cutter diameter 16.5, depth named from the OD, seat center 12 from datum A, keep the Ø16 journal B and the M10 thread, ISO 2768-m general on non-seat dimensions. With STEP + **WOODRUFF SEAT W5, CUTTER Ø16.5, DEPTH FROM OD, 12 FROM A, KEEP B AND M10**, expect a usable automatic planning band on [quote-new.php](https://3dwk.com/quote-new.php). Same geometry with silent “Woodruff for hub, size as needed” often lands DFM notes or **needs_manual**—without inventing any customer PO.

Illustration 2 contrasts a vague RFQ (“standard half-moon key”) versus a labeled width-diameter-depth-keep-out pack and the clearer estimate path.

What widens bands fastest

Unlabeled “standard Woodruff,” a rectangular keyway note reused on a segmental seat, missing cutter diameter or depth, and a seat that eats a journal, undercut, or thread runout. Quantity breaks help unit minutes but do not erase seat-family ambiguity—see [how quantity breaks change CNC unit cost](https://3dwk.com/resources/how-quantity-breaks-change-cnc-unit-cost) and [shoulder fillet versus undercut](https://3dwk.com/resources/shoulder-fillet-vs-undercut-cnc-turned-shafts).

What to do next

Mark each Woodruff seat with a **width, cutter diameter, depth, axial location, and keep-outs**, then upload on [quote-new.php](https://3dwk.com/quote-new.php). Packaging checklist: standard and size if you cite one, seat dimensions the shop must cut, and journals or threads the cutter must not steal. Service pages: [CNC machining](https://3dwk.com/cnc-machining-service.php), [materials](https://3dwk.com/materials.php). Treat **rates.v1.1** min/mid/max as estimates, not invoices. If the UI shows **needs_manual**, answer the seat-family questions rather than forcing a fake price.

Common questions

Is a Woodruff seat the same as a rectangular keyway?

No. A parallel keyway is a rectangular slot; a Woodruff seat is a circular-segment pocket cut by a Woodruff cutter (or equivalent). Reusing a keyway width-and-depth note without a cutter diameter leaves the shape unstated.

Do I have to name the cutter diameter if I name a key size?

Name both when you can. A commodity key size still leaves the shop to infer the cutter and the depth rule. Put the standard, the size, and the seat width, diameter, and depth on the PDF.

Can the seat break into a snap-ring groove or a shoulder?

Only if you say so. A default keep-out is safer: give a minimum land to the journal, the ring groove, and the thread. If the seat is allowed to break a fillet, write that as an explicit exception.

How should I inspect the seat?

Call out the width, the depth (or remaining height), and the axial location from the same datums used on the shaft. Do not leave “fit the key” as the only acceptance note.

Free DFM · 24h quote

Upload CAD → free DFM report

Email required. You get a link to a rule-based manufacturability checklist (not a formal engineering sign-off). Engineers still review pricing.

No CAD? Photo / description → 24h quote

Three fields only — we reply within 24 hours.

Next step

Questions about your design?

Upload CAD files and an engineer will review manufacturability with your quote.

Upload CAD